中义隧道片理化玄武岩段大变形控制技术研究*

为进一步探究高地应力隧道软岩大变形控制技术，以中义隧道主洞片理化玄武岩段为工程背景，提出大变形Ⅰ型支护、大变形Ⅱ型支护、大变形Ⅱ型支护（围岩加固）3种大变形控制方案，以现场试验段监测为辅助验证，采用数值仿真对3种控制方案的控制效果进行对比分析。结果表明:适宜的支护成环时间具有减缓大变形的作用；在衬砌各部位累计最大变形控制方面，控制方案3较其他方案衬砌最大变形最少减小20.8%，且变形时程曲线最终收敛；围岩最大日变形量控制方面，经过开挖断面的进一步优化以及边墙部位塑性区围岩自承能力的提高，控制方案3最大日变形量较其他支护方案至少减小20.8%。结果显示控制方案3能够稳定控制片理化玄武岩大变形，且效果最好，研究结果可为类似工程提供设计依据。     

高含CO2天然气运输管道缓蚀剂的筛选

大多数天然气藏CO2含量为10%~98%,CO2在不同的温度、压力条件下腐蚀极其严重。文章主要针对高含CO2天然气运输管道腐蚀的问题,开展缓蚀剂的筛选,重点开展CO2腐蚀规律研究与实验,评价环境温度、CO2分压、流动速度对腐蚀规律的影响,明确缓蚀剂的影响因素,结合管材的材质,优选评价不同类型的缓蚀剂,缓蚀效率分别为90.53%和92.64%,在管道凝液介质的气相及液相中都有较高的缓蚀效率。通过设计现场加药工艺及制度,监测评价缓蚀剂缓释效果和腐蚀情况,可防止管道运输过程中CO2腐蚀的侵害,长输管线内腐蚀控制良好。     

基于力学机制的钢筋混凝土柱抗剪承载力模型∗

为了兼顾钢筋混凝土(RC)柱抗剪承载力分析的计算精度和简便性,研究建立了一种基于力学机制的RC柱抗剪承载力简化模型。首先基于变角桁架-拱模型理论,结合变角桁架模型的力平衡条件以及变角桁架模型和拱模型之间的变形协调条件,建立了RC柱抗剪承载力分析的理论模型;然后利用38组试验数据进行统计分析,分别确定了混凝土、箍筋和拱模型的抗剪承载力贡献系数近似取值,在此基础上建立了R C柱抗剪承载力分析的简化模型;最后通过与试验数据进行对比分析,验证了该模型的计算精度和适用性。分析结果表明,该模型不仅可以合理分析混凝土、箍筋和拱作用的抗剪承载力贡献,具有较高的计算精度,而且计算公式较为简洁。     

BIM技术在钢结构建筑抗震减灾管理中的应用

为提高钢结构建筑抗震减灾性能,降低建筑坍塌风险,研究BIM技术在钢结构建筑抗震减灾管理中的应用方法是非常必要的。利用BIM技术在钢结构建筑整体建造中的动态建模、可视化、信息共享管理以及抗震减灾性能检测等优势,在建筑抗震减灾管理决策阶段,选出最优方案,针对方案中影响建筑抗震减灾性能风险制定管理策略;在设计阶段,创建三维建筑模型,调整存在风险建筑模型数据信息,并通过振荡模拟分析降低风险;在施工阶段,管理钢结构建筑材料,提升建筑构件的刚度,并依据建筑施工阶段的抗震减灾管理原则制定相应的管理方法,实现对钢结构建筑的抗震减灾管理。结果表明,BIM技术可实现抗震减灾管理中的地震波检测,检测结果精准可靠;可提升建筑构件的刚度与承载力及建筑的抗震减灾性能,降低建筑坍塌等风险,实现钢结构建筑抗震减灾管理。     

Strength and tightness evaluation method for pipe flange connections considering thermal effects

The pipe flange connection is widely applied in chemical, power plants, petrochemical, offshore oil and gas industries, and its strength and tightness are significant for the safe operation. However, there are still no practical and applicable strength and tightness evaluation methods for pipe flange connections working in dramatically varying temperatures. This paper proposed an approach to evaluate the pipeline's strength and sealing performance considering thermal effects in actual operating conditions by combining the experimental measurement and thermostructural analysis. The critical thermodynamic parameters are identified through measured temperature data in operating conditions, and then these parameters are used in the thermostructural analysis to obtain the actual temperature and stress fields. Then, the strength and tightness in complex temperature cases can be evaluated accurately. The pipe flange connection of a liquefied natural gas (LNG) fueling station is analyzed to verify the presented method's effectiveness. This method applies to evaluating the pipeline's strength and tightness and can predict the pipeline's performances under extreme temperatures using the tested data within the measurement range and the corresponding thermostructural analysis. Furthermore, the work in this paper also provides a reference for the design and analysis of pipe flange connections working in complex temperature conditions.     

冻融影响下不同岩性岩石物理力学特性试验研究*

为探究冻融循环影响下不同岩性岩石的物理力学性质的差异化响应,对青砂岩、灰砂岩2种砂岩,白色大理岩、麻粒岩2种变质岩开展冻融循环试验和相关力学试验。研究结果表明:在冻融循环过程中,2种砂岩的质量变化幅度明显高于2种变质岩。相较于青砂岩与麻粒岩,大理岩的单轴压缩强度及弹性模量劣化速率最快。冻融前后青砂岩、大理岩的单轴压缩破坏模式发生明显变化。灰砂岩抗拉强度劣化速率显著低于青砂岩。基于单轴抗压强度、抗拉强度的脆性指数表明冻融作用提高青砂岩的脆性。研究结果可为冻融影响下工程岩体的稳定性与安全性评价提供参考。     

高压储氢系统泄漏爆炸事故的动力学演化*

为研究燃料氢气泄漏、爆炸的特性和规律,预防高压储氢系统中氢气泄漏爆炸事故发生,以加氢站为背景,数值仿真45 MPa高压储罐氢气泄漏并引发爆炸事故,分析泄漏爆炸动力学性质以及爆炸波在非均匀氢气浓度中的传播机制。同时,基于泄漏爆炸事故演化的力学机理,开展氢气泄漏爆炸动态风险分析,针对氢气不同泄漏量,建立泄漏扩散形成的气云体积、气云爆炸产生的冲击波与空间x,z方向上危害距离之间关系。研究结果表明:氢气泄漏过程中,气云氢气浓度变化与流场雷诺数具有较好一致性;氢气扩散受到高压储氢罐周围装置影响,流场中氢气浓度分布不均匀;当发生燃烧爆炸事故时,冲击波参数和湍动能变化梯度大;得到复杂布局区域冲击波超压峰值与比例距离之间关系式,其相比于理论方法更精细、计算结果更准确。研究结果可为降低高压储氢系统泄漏爆炸事故后果、采取有效防护措施提供一定依据。     

Effect of oxide-based fluxes on mechanical and metallurgical properties of Dissimilar Activating Flux Assisted-Tungsten Inert Gas Welds

Present investigation is to study the “Effect of Activating Fluxes on Mechanical and Metallurgical Properties of Dissimilar Activated Flux-Tungsten Inert Gas Welds”. Effect of current, welding speed, joint gap and electrode diameter on weld bead dimensions on 6 mm thick dissimilar weld between carbon steel to stainless steel, was studied under Activated Flux-Tungsten Inert Gas Welding process. During this investigation three different types of oxide powders were used-TiO₂, ZnO and MnO₂. After welding samples were subject to mechanical testing, in addition to characterization via micro hardness and microstructures of Normal Tungsten Inert Gas Welds and Activated Flux-Tungsten Inert Gas Welds. Activating fluxes TiO₂ and ZnO are effective fluxes for Activated Flux-Tungsten Inert Gas Welding of dissimilar weld between CS to SS. Highest depth/width (D/W) ratio reported under TiO₂ and ZnO fluxes compare to Normal-Tungsten Inert Gas Welds. Lowest angular distortion was observed under TiO₂ flux compare to Normal-Tungsten Inert Gas Welds. Mechanical properties, Joint Efficiency of Activated Flux-Tungsten Inert Gas Welds are higher than normal-Normal Tungsten Inert Gas Welds. Tensile Test specimens of both the processes failed from the parent metal (carbon steel side). Carbon migration from CS to SS, had occurred which led to failure of weld joints from CS side.     

Microstructure of 2205 duplex stainless steel joint in submerged arc welding by post weld heat treatment

The 2205 duplex stainless steel (DSS) is of both good properties austenitic steel and ferritic steel, which applies to the shipbuilding industry usually. In this paper, the OM, XRD and microhardness test methods are used to analyze the variation of submerged arc welded (SAW) joints with and without post weld heat treatment (PWHT). The research results show that the σ phase disappear in the fusion edge zone near heat affect zone (HAZ) and an increase in the welded center zone during the follow-up PWHT, while the amount of γ phase is decreased in the welded center zone with PWHT. A segregation distribution of some second phases is also found in the welded center zone after PWHT. There have two pick values of microhardness arise in the fusion edge zone and the welded center zone separately without PWHT. However, a maximum value of microhardness at the fusion edge zone near HAZ is disappeared and the other is still held at the welded center zone during PWHT. It can be attributed to the changes of second phases, element diffusions and particle segregation during PWHT. A developing mechanism is issued to demonstrate the second phases transferring of the 2205 DSS SAW joints by PWHT.     

45~#钢在西双版纳大气环境下的腐蚀研究

目的研究西双版纳热带雨林地区大气环境下材料的初期腐蚀行为。方法使用45#碳钢在西双版纳大气环境下进行1年的大气暴露腐蚀试验,并利用质量损失分析、SEM、XRD和FTIR等技术,分析45#碳钢在西双版纳大气环境下暴露1年的腐蚀行为。结果 45#碳钢的腐蚀产物以γ-FeOOH,Fe(OH)3和Fe3O4为主,并有少量的α-FeOOH。结论西双版纳大气环境腐蚀性为C2级。在暴露1年的时间内,锈层化学稳定性随试验时间的延长逐渐增强,对基体的保护性逐渐加大。